Installing a New Shower Unit
An licensed plumber near me effective shower setup needs mindful preparation and a lot of work. In most cases, you will need to do 3 kinds of tasks: framing walls, setting up the plumbing, and completing walls.
Preparation
Firstly, you should pick the kind of shower that you wish to install. It is very important to establish whether the chosen shower is capable of coping with specific systems and can regulate a safe level of water through the boiler. Many shower systems nowadays are created to be versatile to different water pressures (such as stored warm water and cold mains).
It is likewise important to take into account the water pressure and the planning of the piping and drain for the shower
Different Kinds of Shower Units
Push-on Mixer: The tube and spray parts of the push-on mixer shower system can be linked to the bath tap as per your requirement, and the water temperature level can be adjusted by means of the taps. Push-on mixers are inexpensive and extremely simple to set up. However, although the hose connection is easy, it is easily dislodged. Additionally, it is inconvenient to change the temperature level.
Bath/ Shower Mixer: The hose pipe and spray of this type of shower are combined with a bath mixer tap, and the temperature can be adjusted through the bath taps. It is a very cheap choice and no extra pipes is involved. However, the bath/shower mixers likewise experience inconvenient temperature level control alternatives.
Manual Mixer: The hose and spray of a manual mixer shower unit are a part of the wall unit and the cold and hot water materials are linked to a single valve The temperature and pressure of the water are managed through either one or a range of knobs (in more pricey showers). Although temperature control is a lot easier in manual mixer types, they are more expensive than the formerly pointed out mixers. They also require extra pipes of cold and hot water system pipes.
Thermostatic Mixer: The hose pipe and spray of this shower type belong of the wall system and the hot and cold water materials are linked to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to prevent it from becoming too hot. One of the biggest advantages of a thermostatic mixer shower type includes practical temperature control. Nevertheless, it is the most expensive of the various mixer options.
Power Shower: A power shower is a single system including an effective electric pump that can altering both the water pressure and temperature level. This type of shower can be fitted if there is supply of water from a cold water cistern and a hot water cylinder. A power shower makes the adjustment of both pressure and temperature level simple. On the other hand, it disagrees for water heated up straight by the shower or where the water is supplied by a combination boiler under mains pressure.
Electric Shower: An electric shower is plumbed into a mains cold water supply and it heats up the water electrically. It is important to keep in mind that for this shower type to be installed, the mains pressure needs to be a minimum of 0.7 kg/sq cm (10lb/sq in). The system enables the temperature and pressure to be changed via a knob. Models with temperature stabilisers are better as they remain untouched by other taps in other places in usage within the household. A major drawback of electric showers is that the control knob just enables the alternative of high temperatures at less pressure, or lower temperature levels at a greater pressure. This is bothersome in the winter when the spray is frequently weak and the mains water is chillier. Nevertheless, this issue is taken on in some designs which are readily available with a winter/summer setting.
Method
Depending on the type of shower you wish to set up, the shower head need to either be fitted in order to prevent its contact with the water in the bath listed below or the base tray, or it needs to have a check valve.
Before beginning, it is advisable to mark the positions of the shower head and control, and to plan the pipe-work involved. Additionally, the drain system to eliminate the waste water will require to be planned. Both positions of the cable television path and the shower switch will likewise need to be considered if a rapid or electric shower system is being installed.
Use the guideline guide supplied with the shower unit to fit the shower control.
Before fitting the pipes that will provide the water to the shower system, it is very important to cut off the supply of water. In order to protect the pipes, they ought to be provided a waterproof covering and likewise fitted with isolating valves. The pipelines can then be buried into the wall and plastered over to neaten the general look.
Fit the base tray, shower head, and fittings.
Connect the main shower control to the pipes that will be supplying the water (This may require a female screw thread adapter).
Reconnect the supply of water and test the pipes for any leakages, as some may need tightening.
If you are installing an electrical shower, keep in mind to switch off the electricity supply before making any electrical connections. Once these connections have actually been made (there ought to be guidance within the instruction manual), the power supply can be changed back on.
Adjusting Water Pressure to Match Your Shower
The cold water tank can be raised to a higher height (often as little as 150mm (6inches)) by fitting a strong wooden support below it-- possibly composed of struts and blockboards. If you select this choice, the primary and distribution pipes will also need to be raised to meet the brand-new height of the reservoir.
Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is selected, it needs to be linked into the power supply in order to operate.
Piping and Drainage
It is best to use 15mm size supply pipes, and make the runs to the shower as brief and straight as possible so as to maintain optimal pressure and reduce heat loss. In addition, by minimising using elbows for pipe corners, you can decrease the resistance in the flow of the water supply. You can attain this by flexing the pipes instead.
Most Common Mistakes
# Breaking or disregarding local code restrictions.
# Using pipes that are too small.
# Attaching copper to galvanized without utilizing a brass or dielectric fitting between the two.
# Not using tape or pipe substance at threaded joints.
# Not leveling your fixtures when installing them.
# Not setting up an air space filling for fixtures.
# Cutting supply stub outs too brief to install the shutoff valves onto after the finished wall is in place.
# When turning the water back on in your house, constantly run the outdoors pipe valve or flush your toilets to bleed dirt and air from the lines. This particles can trigger issues in your sink faucets and other pipes trim.